Rv Sink, Lavatory, ABS/Acrylic Capped, White, 13" x 10-1/4" x 5 1/2"

RV Lavatory Sink - Oval - 13"x 10 1/4" x 5 1/2" (White)

Drop-in ABS/acrylic-capped lavatory camper sink,13" x 10-1/4", white, has a brighter shine and resist stains and scratches better than plastic. Features hold down clips and includes mounting hardware.

RV lavatory sink, 13" x 10 1/4" x 5 1/2" , white,  is made from high gloss acrylic backed with fiberglass.  It has a 2"  drain. All mounting hardware is included.  This is designed for top mount or undermount install.

Features

• High gloss acrylic is easy to clean and wear resistant
• Fiberglass insulation provides quiet performance, temperature stability and strength
• Easy to install for both new construction and remodel projects
• Simple tab and clip system make installation easy
• Installation instructions include sink cut out dimensions
• Reinforced drain

 Sink dimensions 13" x10 1/4" x 5 1/2"

Countertop cut out dimensions are 31 1/4" x 20 1/4"

Manufactured by Lyon's Industries.


Additional Colors:

Part Number	Size	Color
881491	13” x 10 ¼” x 5 ½”	Brushed Nickel

REPLACING YOUR OLD SINK:
No cutting of your existing countertop is necessary. Simply place the sink in the hole and makesure the rim of your new sink rests on your countertop. If you need to adjust the hole size, use a saber saw or keyhole saw then continue with the instructions below.

MOUNTING SINK IN A NEW COUNTERTOP:
+ Place the sink upside down on the countertop in the desired location.
+ With a pencil, trace a line around the outside edge of the sink onto the countertop.
+ Remove sink from the countertop.
+ Measure in 7/8" and draw new lines inside the fi rst sink outline just drawn. Radius corners
are not required. As a reference please see cut out dimensions on next page for your product.
+ Cut out the countertop on this new line.
+ Trial fit your sink into the hole, making sure it is centered where you want it.
+ Remove sink. Use a good grade of silicone caulk/adhesive and apply a bead under the
lip of the sink, then replace the sink in the hole.
+ Attach sink to countertop with bolts and clips provided-see below. Hand tighten bolts
only with three rotations. (Fig. 1)
IMPORTANT — Do not over tighten bolts. Sink will damage if bolts are over-tightened.
*Note: It's not necessary for the bolts and clips to be installed. Their primary purpose is to hold the sink in place while the adhesive dries. If there isn't clearance for them, follow steps 1-7 and fill sink with water to hold in place while adhesive dries.
+ To finish the job, fill any variances between counter top and sink by sealing outside of
sink with a good grade of color-matched or clear silicone caulk/adhesive.
+ When installing drain to sink make sure to use a high grade silicone caulk or latex.
Do not use plumber’s putty.

CARE AND CLEANING INSTRUCTIONS
+ Clean surface with nonabrasive liquid detergent and warm water. Use cleaning
products such as Soft Scrub Gel®, Comet Gel®, Gel Gloss® or other similar products.
+ DO NOT USE ABRASIVE CLEANERS, "steel wool" or wire brushes on surface. Caustic drain cleaners may cause surface damage. Open flames (cigarettes, candles, etc.) may damage surface.
+ Surface damage-light scratches, dulled areas, and small cuts and are restored by first
scrubbing with automotive-type white body cleaning compound, such as Meguire's #9
Swirl®Remover, followed by an application of Gel Gloss®.

Repair Instructions.
+ Remember to always use a cutting board or sink protector when using knives or sharp
objects in your sink.
+ Recommendation: When pouring boiling water or placing hot pots or pans into the sink, run some cold water simultaneously.
WARNING: Some cleaning products are not suitable for use. Read all labels carefully.
DO NOT USE if they say “not suitable for use with ABS, acrylic or polystyrene”.

RV Lavatory Sink - Oval - 13"x 10 1/4" x 5 1/2" (White)